Scoubdious de (God-zilla Mode)

A 2 by 1 with one line of corkscrews and then 3 hexagons. Repeat until done.

Godzilla_Mode a écrit:

An assymetrical regular pentagon ( I usually make twisted pentagons) going into a 2 by 1 corkscrew. Then 5 lines of triangle on one side, then a single 2 by 1 corkscrew stitch and then I make 5 triangle stitches on the opposite. Repeat until done.

Pentagon ? Sure?

My mistake. It's a hexagon.

A 1 by 1 box stitch where I tied knots with 2 strings and used the same configuration in the next line to see if I can get colors to change.

1 by 1 alternating box/nautilus stitch going into a Chinese staircase and ending in a circle
 stitch.

A Chinese staircase going down into two sets of 1 by 1 box stitches, then a cross stitch, then into a 3 by 1 and again finishing in a Chinese staircase.

A 2 by 1 nautilus box stitch going into a 1 by 1 box stitch with the four main strings. I took the thin base string and tied a knot on between each 1 by 1 box stitch.

A 2 by 2 twist going into a 2 by 1 corkscrew that I wrapped around a 1 by 1 circle stitch. I then finished it into a 2 by 1 corkscrew.

[url=https://servimg.com/view/20366620/1181][/url]




A 2 by 1 box stitch made into two triangulation box stitches. Going into a 2 by 1 chevron, then parallel cobra stitches. Those stitches were formed into a small circle then back into a 1 by 1 chevron and finishing in those two triangular stitches.

A scoubitunel going into 2 triangles and a twist. I then took the remaining string to bottle and attach the remaining strings. This was eventually finished in a 1 by 1 circle stitch.

A 2 by 1 swirl stitch that I then added string in the center to make a 1 by 1 circle stitch. I then wrapped the initial 2 by 1 swirl strings around the center swirl stitch. As a result the center of the 3 by 1 looks bottled.

These are the first two butterfly stitches I have ever made. The red and blue lanyard has a butterfly stitch up top, going into a Chinese staircase and then a 1 by 1 box stitch at bending 90 degree angle stitches.

A butterfly wrapped around the top quarter of a 2 by 1 corkscrew

A 3 by 1 corkscrew where I made 3 stitches around the center of a pencil and then pulled the pencil out and restarted the process.

[url=https://servimg.com/view/20366620/1211][/url]



3 alternating (modified) Chinese staircase stitches lines that formed a circle with a staircase down the middle. I then took a regular, violet Chinese staircase and wrapped around the center. I then took all the excess string and made a large Chinese staircase wrapped around that. I finished with a 3 by 1 alternating brick and corkscrew stitches.

A 3 by 1 corkscrew with a nautilus stitch on one of the stitches. I then cut went down into a 1 by 1 circle stitch and into 2 1 by 1 circle stitches after I cut and added some string. Then a 3 by 1 corkscrew around a 1 by 1 circle stitch except that the bottling is in the center.

I made a 1 by 1 circle stitch and then made a bottle stitch around it three times.

A megalace butterfly stitch that I made into a circle tied to alternating 1 by 1 box and circle stitches by a string in the back.

½



4 strings layered to make 2 seperate strings made into a larger butterfly stitch.

Quad with 2 rows of 1 by 1 box stitches going down into a 1 by 1 circle stitch with overhand knots (done with the silver strings) going down into a 3 by 1 corkscrew.

Two levels of a wave stitch going into a 2 by 1 super brick and a 2 by 1 corkscrew alternating on each side. It then went 4 by 1 corkscrew where I took a 1 by 1 circle stitch and wrapped several strings around it.

These pictures are turning out huge for some reason. This is a 3 by 1 superbrick going into the new modified bottle stitch I've been using (although this is the first time ive used this modified bottle stitch on a superbrick). I then used a cross stitch to make sure my designs liner up. I then added string to go from a 2 by 2 quad into a 3 by 2 quad ( a rectangle I guess?).

https://www.instagram.com/yo_mommas_lanyards/

I made a 1 by 1 box stitch in the center of 4 strings after tying a knot in the center and making 1 by 1 box stitches in each direction.

I then cut strings from the top part of the scoubidou to transition into a 1 by 1 circle stitch, with the clear string only. I then finished in a 2 by 1 alternating superbrick and corkscrew stitches after adding the previous strings I cut from the top.

https://www.instagram.com/yo_mommas_lanyards/

I made a 1 by 1 box stitch in the center of 4 strings after tying a knot between those four strings and making box stitches down each side. I then took the string that hung out and made swirl stitches with the extra strings from the initial stitch being secured with a chinese staircase and knits between each swirl stitch.

https://www.instagram.com/yo_mommas_lanyards/




[url=https://servimg.com/view/20366620/1293]
[/url]

I made a 1 by 1 box stitch, made a butterfly stitch, made both circular. Glued one on top of the other. Cut strings from both and when into a 1 by 1 box stitch. After that I then went from a pentagon, to two triangle stitches and then a 2 by 1 corkscrew

https://www.instagram.com/yo_mommas_lanyards/